01.030.0703: Shelf Angle Detail - Typ. Face Brick, Term Bar This shelf angle detail uses a typical brick course below the shelf angle. This may result in a wider horizontal expansion joint below the angle, but is more economical than using a lipped (notched) brick. The shelf angle is flashed with flexible thru-wall flashing, transitioning [...]
06.130.0204: Floor Tile - Over CBU & Cork on Concrete This detail shows tile laid on cementitious backer unit (CBU) w/ taped joints on a concrete subfloor, with cork underlayment separating the tile assembly from the concrete for soundproofing. The tile is adhered to the CBU using a dry-set or latex-modified portland cement mortar bond [...]
06.130.0203: Floor Tile - Thinset on Concrete This detail shows tile adhered to a concrete subfloor using a dry-set or latex-modified portland cement mortar bond coat. This detail is based on TCNA Method F113. DOWNLOAD DETAILDynamic 3D Detail Explore this detail and download the Sketchup Model in the 3D Warehouse. Explore Detail
06.130.0202: Floor Tile - Thinset on Concrete or Cured Mortar Bed This detail shows tile laid on a concrete slab or a cured mortar bed. The tile is adhered using a dry-set or latex-modified portland cement mortar bond coat. If required, an antifracture / waterproof membrane is applied over the cured mortar bed or concrete. [...]
06.130.0101: Floor Tile - Over CBU on Wood Subfloor This detail shows tile laid on cementitious backer unit (CBU) w/ taped joints on a wood subfloor. The tile is adhered using a dry-set or latex-modified portland cement mortar bond coat. The wood subfloor has 1/8" gap between the exterior glue tongue & groove plywood sheets, [...]
02.010.1303: Control Joint - Fire-Rated This detail shows block with flat ends being used at the vertical control joint. Fireproof material resides at the vertical CJ, along with sealant and backer rod. This detail allows shrinkage of the block, but does not resist lateral loads. There is horizontal joint reinforcement at 16" o.c. vertically in [...]
02.410.0132: High Lift Grouting Procedures This detail shows a concrete masonry (CMU) wall grouted using high lift grouting procedures. Vertical reinforcement is shown with optional rebar positioners, and vertical bars overlap to achieve sufficient development strength per structural design. Grout is applied vertically in lifts between 5'-0" and 12'-8", therefore cleanout openings may be required [...]
02.410.0131: Low Lift Grouting Procedures This detail shows a concrete masonry (CMU) wall grouted using low lift grouting procedures. Vertical reinforcement is shown with optional rebar positioners, and vertical bars overlap to achieve sufficient development strength per structural design. Grout is applied vertically in lifts not to exceed 5 feet, therefore cleanout openings may not [...]
02.120.0851: Blank at Bearing Wall - Top of Wall This detail shows a precast concrete plank bearing at the top of an exterior CMU wall. The wall has horizontal joint reinforcement at 16" o.c. vertically. The plank has continuous reinforcement and grout at the keyways, tying the floor to the wall with bent bars. The [...]
This site uses cookies
Small text files that are placed on your machine to help the site provide a better user experience. In general, cookies are used to retain user preferences, store information for things like shopping carts, and provide anonymised tracking data to third party applications like Google Analytics. As a rule, cookies will make your browsing experience better. However, you may prefer to disable cookies on this site and on others. The most effective way to do this is to disable cookies in your browser. We suggest consulting the Help section of your browser or if you decline you will be redirected to the About Cookies website which offers guidance for all modern browsers.
01.030.0751: Roof Detail – High Wall – Low Roof DOWNLOAD DETAIL [PDF]Dynamic 3D Detail Explore 3D Detail 
01.030.0703: Shelf Angle Detail - Typ. Face Brick, Term Bar This shelf angle detail uses a typical brick course below the shelf angle. This may result in a wider horizontal expansion joint below the angle, but is more economical than using a lipped (notched) brick. The shelf angle is flashed with flexible thru-wall flashing, transitioning [...] 
06.130.0204: Floor Tile - Over CBU & Cork on Concrete This detail shows tile laid on cementitious backer unit (CBU) w/ taped joints on a concrete subfloor, with cork underlayment separating the tile assembly from the concrete for soundproofing. The tile is adhered to the CBU using a dry-set or latex-modified portland cement mortar bond [...] 
06.130.0203: Floor Tile - Thinset on Concrete This detail shows tile adhered to a concrete subfloor using a dry-set or latex-modified portland cement mortar bond coat. This detail is based on TCNA Method F113. DOWNLOAD DETAILDynamic 3D Detail Explore this detail and download the Sketchup Model in the 3D Warehouse. Explore Detail 
06.130.0202: Floor Tile - Thinset on Concrete or Cured Mortar Bed This detail shows tile laid on a concrete slab or a cured mortar bed. The tile is adhered using a dry-set or latex-modified portland cement mortar bond coat. If required, an antifracture / waterproof membrane is applied over the cured mortar bed or concrete. [...] 
06.130.0101: Floor Tile - Over CBU on Wood Subfloor This detail shows tile laid on cementitious backer unit (CBU) w/ taped joints on a wood subfloor. The tile is adhered using a dry-set or latex-modified portland cement mortar bond coat. The wood subfloor has 1/8" gap between the exterior glue tongue & groove plywood sheets, [...] 
02.010.1303: Control Joint - Fire-Rated This detail shows block with flat ends being used at the vertical control joint. Fireproof material resides at the vertical CJ, along with sealant and backer rod. This detail allows shrinkage of the block, but does not resist lateral loads. There is horizontal joint reinforcement at 16" o.c. vertically in [...] 
02.410.0132: High Lift Grouting Procedures This detail shows a concrete masonry (CMU) wall grouted using high lift grouting procedures. Vertical reinforcement is shown with optional rebar positioners, and vertical bars overlap to achieve sufficient development strength per structural design. Grout is applied vertically in lifts between 5'-0" and 12'-8", therefore cleanout openings may be required [...] 
02.410.0131: Low Lift Grouting Procedures This detail shows a concrete masonry (CMU) wall grouted using low lift grouting procedures. Vertical reinforcement is shown with optional rebar positioners, and vertical bars overlap to achieve sufficient development strength per structural design. Grout is applied vertically in lifts not to exceed 5 feet, therefore cleanout openings may not [...] 
02.120.0851: Blank at Bearing Wall - Top of Wall This detail shows a precast concrete plank bearing at the top of an exterior CMU wall. The wall has horizontal joint reinforcement at 16" o.c. vertically. The plank has continuous reinforcement and grout at the keyways, tying the floor to the wall with bent bars. The [...]